paulglass46

Fiat 500 Replacement Key Fob If your remote key fob isn't working, it's time to replace the battery. If you replace the battery, but it still doesn't work it could be a problem somewhere else. United Locksmith specializes in the production of new keys for classic automobiles. We have all the necessary tools and parts to perform this service. Dead Coin Battery A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob has a coin cell battery that is prone to draining quickly when it isn't being frequented enough. If your remote started to show signs of weakness like a loss of range or stopped working completely, the battery is probably dead. The battery inside the key fob is held in place by steel clips that retain it. If the clips aren't secure, they could cause contact problems that will prevent your remote to receive power. By using a small flathead screwdriver, pry the retaining clip open to remove the current battery and then insert a fresh one. Be sure to choose a replacement with the same type of voltage, size, and specification as the original battery. The key fob might be damaged or corroded due to exposure to water. Even a short bath in soapy water may harm the electronic chip within. fiat 500 key fob to keep your key fob in a dry location. Water Damage If your key fob isn't working properly, it may be caused by water damage. The rubber seals on key fobs protect them from getting damaged by a small drizzle or splash of water. However, it's crucial to keep the car keys away from the washing machine, the ocean, and pool. The key fob contains an electronic chip that sends a message to the immobilizer system of your vehicle. This is the reason why your 500 can lock or start, but should the chip become saturated, it won't be able to longer function. You can try cleaning the inside of your key fob's electronics using isopropyl alcohol or an electronic cleaner to see if they are still good. However, it is probably recommended to purchase a replacement from a dealership instead of trying to repair the key fob which is submerged in salt water. Although a replacement fob may cost a bit of money, it is a lot cheaper than paying for your Fiat 500 to be towed to the dealership and repaired! You can also do it yourself with only a few steps. Be sure to have the correct type of battery before attempting to open your key fob. There are step-by-step directions for any car keyfob online. Faulty Chip The chip inside the key fob connects directly with the immobiliser on your car to ensure that the vehicle will only start when the proper keys are inserted. If the chip is damaged, or corrupted in any way it will not start. A chip that is damaged can happen due to several reasons, but most often it is due to water damage or a dead battery. It is best to hand over the work to a professional locksmith, who can repair the chip in a short time and at a reasonable cost. If your key fob ceases to function after exposure to clean tap water or rain, take off the battery and clean the electronic component with a towel to ensure it's completely dry before putting it back into. If the key fob will not work, there is an opportunity that it is a fried component and needs to be replaced. Some people go to their dealer if they need an entirely new Fiat fob. However, this could be expensive. If you are seeking a cost-effective solution to get your Fiat key fob fixed, look no further than United Locksmith. We have the tools and knowledge necessary to repair your Fiat key fob in a quick and professional way. Faulty Receiver Module Fiat key fobs transmit an electrical signal to the vehicle which will unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However there are some things that can cause the fob to stop working. This could be due to a dead coin battery, water damage buttons, worn ones, a receiver module issue and signal interference, or a malfunctioning electronic chip. If the fob was placed in the pocket that has been subject to severe trauma (such as being dropped on the hard floor or washed in the washing machine), it may not be able to connect with the Body Control Module (BCM) of the car. This is because the BCM is a secure system that can only accept signals from a genuine original key and not accept any other. If this is the case, then you will require replacing your fob. A professional locksmith will take care of the entire replacement process including programming a brand new key for your 500. They can even provide the fob cloned to work the same as the original (and costs just a fraction of the price).